Flatware To-Go Kits
This DIY project can be completed in an afternoon and makes a thoughtful eco-conscious gift.
This post will cover how to make little zip pouches to hold flatware, chop sticks and a cloth napkin. The instructions for simple mitered-corner napkins can be found here.
About the Fabric
To keep with the spirit of sustainability, I chose recycled canvas for the outside of the pouches in the Flatware To-Go pattern. For the inner lining I opted for an organic cotton in a coordinating Checkerboard pattern. The napkins also used similar fabrics.
These fabric designs are from my Avocado Toast Collection available from Spoonflower.
Follow manufacturer recommendations for pre-washing the fabric. You may wish to iron the cotton. The canvas won’t need to be ironed, but you may wish to zig-zag stitch or serge around the raw edges to prevent excess fraying.
Notions and Suppies
In addition to the fabric you will need:
- Thread to match or complement your fabric. I used a medium brown color for clarity, but you may wish to use a less obvious color.
- One 14″ nylon zipper to match or complement your fabric. I love bright zippers that standout and become a design element.
- One 3.5″ piece of 1/2″ twill tape or ribbon
- Flatware and chopsticks. You can go with bamboo for a truly sustainable kit, but I prefer metal flatware. Second hand stores are also a great resource.
- Napkin. Make your own with these instructions.
NOTE: Click on any of the photos to enlarge. Click on “x” in upper right corner to close zoomed view.
STEP 1 – Cut bag pieces
- Cut one 10 1/2″ x 7 1/5″ piece from recycled canvas for bag outer.
- Cut two 10 1/2″ x 4″ pieces from cotton fabric for bag lining.
STEP 2 – Pin to layers to zipper
Layer as follows, aligning long edges:
- Outer bag fabric, face up.
- Zipper with the pull facing down (toward the outer fabric). The zipper should extend an inch or two beyond the fabrics.
- First piece of lining fabric, face down.
Pin all layers together along length of zipper.
STEP 4 – Repeat step 2
Repeat for the other zipper side. Align outer layer, zipper with pull facing down, and second piece of lining fabric. Pin layers together.
HINT: Start with zipper closed to aid in aligning front and back of bag. Before sewing, open zipper so that the head/pull are clear of stitching area.
STEP 6 – Turn bag right side out
Open up the seams so that the right sides of the fabric face out.
Fold the lining fabric to the inside of the bag.
NOTE: Normally I would press the seams open at this point, but the zippers I purchased melt too easily. I had to scrape a bit of colorful nylon off the metal plate. So learn from my mistakes. Either finger press, or cautiously find a temperature setting that works for you.
STEP 7 – Top stitch along zipper opening
STEP 8 – Insert twill loop and pin first side seam
Partially close the zipper. You will be working on this closed end first. Fold the bag over with right sides together.
Fold your twill ribbon in half and insert inside bag between zipper layers. The photo above indicates placement.
If using tape with text on it, as I am, make sure it reads correctly as shown here. I messed one up before I paid attention to it. Again, learn from my mistakes.
Take care aligning the zipper, as well as the grid for your outer layer. If you are using the Flatware To-Go fabric, the blocks should align perfectly for a neat seam.
STEP 9 – Stitch side seam
Using a 1/4″ seam allowance, stitch side seam.
There is a lot of bulk at the zipper/twill loop section. Shim the back of the presser foot to assist in getting over this bump. My machine came with this handy tool pictured above, but you can also use a piece folded fabric. Place it under the foot behind the needle when you start over this section.
You may also wish to hand turn the wheel until you are past the thick layers.
STEP 13 – Pin and mark for box corners
Spread a corner of the outer fabric and fold at an angle so it resembles the image above. Be sure your seam is centered on the fold. Pin to secure.
HINT: If your outer fabric is the Flatware To-Go pattern and you want to be sure the grid is squared up, hold your folded fabric up to a bright light or window so you can see the print. Tweak the alignment as needed.
Measure 1″ from the corner on both sides and mark with a fabric pencil. Connect the marks with a straight line across.
NOTE: The box corner is optional. I like the look and shape of a box corner on my pouches or bags. You can opt to skip to step 15 if you prefer an easier construction or just want a flat pouch.